AC Motor - Types, Principle, Construction & Working
What is AC Motor: Types, Principles, Constructions & Working
What is AC Motor?
AC motors use magnetic fields and an external power source to create rotary motion. An AC motor converts electrical energy into mechanical energy, it has a stator and rotor. The stator is the stationary spinning part of the motor which typically looks like one or more metal bars through which many wires are wound. These wires carry the electric current that windings of wire on the rotor convert back into mechanical force to spin it. The strongest magnetic field created is concentrated in this part of the setup because that's where there are more turns on coils of wire. An AC motor is an electric motor that runs on an alternating current (AC). It is the most common type of motor used in industrial applications today.
Working of an AC Motor?
An AC motor has coils that are wired in the opposite direction of the usual electric current. Instead of the earth having a negative charge, it has an opposite positive charge and vice versa. When these coils are switched on by an electromagnet, they induce electric currents in these oppositely charged wires by working against the effects of conventional electrons. Movement is caused when this resistance takes place in response to two different magnetic fields generating electricity with opposing directions so that power goes in one direction when the west's field is in control and power goes eastward when the east's field is exerting its force. Consequently, it will spin one way until the difference between west and east forces becomes too great to overcome at a point.
Types of AC Motors?
The two major types of AC motors they are as follows:
1. Induction (sometimes called synchronous) and
2. Permanent magnet (sometimes called asynchronous)
1. Induction motors and synchronous motors:
Induction motors are the most common type, and they work by using a rotating magnetic field to induce a current in the rotor. Synchronous motors work by using a permanent magnet on the rotor to synchronize with the AC current.
AC motors are available in a variety of sizes and power ratings, and they can be used for a wide range of applications, from small appliances to large industrial machines.
High efficiency - AC motors are very efficient, and can achieve efficiencies as high as 95%. This is much higher than the efficiency of DC motors, which typically range from 50% to 70%.
Synchronous motors are found in electrical grids because they can be controlled by varying the frequency at which they are driven. Synchronous AC Motors do not tend to self-rotate so will operate more quietly but are not suitable for use at grid frequencies.
The major difference between the two kinds of motors is the way they generate the rotating magnetic field needed for driving. A permanent magnet motor also does not need an outside source of electric power but requires more starting torque than an induction motor before it will run at full speed. As it typically needs less maintenance, one study finds that approximately three-quarters of all large industrial drives use this type of motor. Permanent magnets require only aluminum transistors to function whereas pushing 1/4 horsepower through an induction motor without brushes requires over 12 pounds of copper wire - so use whichever your levels can handle!
Synchronous motors use rotating magnetic fields synchronized with the AC supply frequency (50 or 60 Hz) to create torque. Synchronous motors produce large amounts of starting torque, which is useful for heavy loads such as those found in industrial applications..
It's different from an asynchronous induction motor or brushless DC motors which need to be running before any torque output will manifest. The power spectrum of the motoring current shares the same harmonic relationship as the Alternating Current frequency. This behavior causes better commutation because synchronism matches both ends of each electrical cycle with phases between transistors switching on and off.
Answer: A synchronous AC motor has the rotor spinning in time to the frequency of the electrical current. So no back-EMF spikes are coming from the armature, but because it rotates at a constant speed, large load variations can cause power swings over time, which must be damped to prevent these power peaks. Synchronous motors are commonly used for traction applications where large load variations are expected.
2. Permanent Magnet motors:
Permanent magnet motors use magnets to create the rotating magnetic field. These motors are smaller and lighter than induction or Synchron synchronous motors, but they are more expensive. Permanent magnet motors also have a higher efficiency than induction motors.
A permanent-magnet AC motor (PMAC) is a type of electric motor driven purely by AC power. It consists of an armature with coils on the rotor, and the field poles on the stationary stator are magnets that provide magnetic interaction to produce torque. Typical designs use -shaped (although other shapes are possible) steel laminations for the majority of flux path, with rare-earth magnets providing current confinement in gaps around pole pieces. PMACs may also employ inductive windings for extra reactive reluctance torque production; these are used either when back EMF is inadequate for full bearing loads or where desiccated bearings would pose problems due to limited airflow.
A Permanent magnet motor is a type of electric motor that uses permanent magnets to create the rotating magnetic field that powers the motor. Unlike an induction motor, which uses an alternating current to create the rotating field, a Permanent magnet motor uses Permanent magnets to create a static field. This has the advantage of not requiring an AC supply, which makes them useful for applications where a reliable power supply is not available. Permanent magnets also have a higher efficiency than induction motors, making them more efficient to run.
Permanent magnets are made from materials that have a permanent magnetic field, such as iron, nickel, and cobalt. They can be in the form of a magnet block, bar, or plate. Permanent magnets are made from Permanent magnets by cutting them into small slices and then sorting the resulting chips; Permanent Permanent magnets made in this manner do not lose their magnetic properties.
Many permanent magnet motors provide very consistent torque, hence the use in applications such as electric vehicles. The consistency and torque can be ideal for making less electronic noise and saving batteries onboard an electric vehicle; the term "continuous sine wave" is often used to describe these types of motors.
Principles & Construction of AC Motors?
AC motors have two main principles of operation: different speeds and different torque. They work on the principle of the rotation of a circuit from high voltage, low amperage to a low voltage, high amperage.
AC motors first create a rotating magnetic field with an AC that is switched on and off at a constant frequency. So if the resulting magnetic field rotates clockwise, then applying a DC in one direction will cause clockwise rotation as well as attraction forces to other nearby magnets or ferrous materials such as iron cores or steel laminations. In contrast, reversing this polarity by switching on the same magnitude DC in the opposite direction will reverse both rotation and attraction force directions from those before reversal
The brushing motors of the past would wear out quickly because their brushes would constantly contact parts of the armature with high voltage. Therefore, synchronous motors were developed. Synchronous motors are induction motors that operate on a single-phase power source - hence their name "single-pole, single-phase" (1P1). Synchronously operating induction motors have two poles on shafts surrounded by stationary magnets. The electrical current alternates between these poles.
AC Motor is that the rotation of the motor is caused by alternating electric current traveling through the coils. The direction of this current flows changes at a specific frequency. This speed can be determined using a copper wire that creates a magnetic field when energized by electrical pulses, and it travels through the wires in one direction until reversing course to travel in the opposite direction back to its starting point. When moving in one direction, electrons flow away from it towards another coil, inducing an electric charge or voltage on its core’s two windings which turns out to be what causes electromagnetic induction within each coil when it reaches Faraday’s law.
Post a Comment